Front Stainless Braided

Stoptech Stainless Steel Braided FRONT & REAR Brake Lines Toyota 4Runner 03-18

Stoptech Stainless Steel Braided FRONT & REAR Brake Lines Toyota 4Runner 03-18

Stoptech Stainless Steel Braided FRONT & REAR Brake Lines Toyota 4Runner 03-18
This listing is for a brand new set of Stoptech Stainless Steel Brake Lines. This set of SS brake lines provide a quicker pedal response, maintaining consistent brake pressure and precision brake modulation, especially during threshold braking. Adding a set of StopTech Stainless Steel Brake Lines to your performance vehicle will provide an immediate improvement to brake performance and pedal feel from the very first stop. Stoptech braided brake lines protect against the elements of harsh driving conditions. Built to match your exact requirements. Brake Lines and Installation Hardware. StopTech brake lines consist of a PTFE (commonly referred to as Teflon) inner line that carries the brake fluid, which is then covered with a layer of stainless steel woven braid. The PTFE tube is very resistant to expansion under pressure and will not degrade from exposure to brake fluid. Advantages of StopTech Stainless Steel Brake Lines. Includes all hardware needed for safe and proper installation. Compliance with TUV and FMVSS 106 safety standards. Quicker response time shortens stopping distance. 100% Tested to 4,500 PSI. Improved pedal feel and modulation. Strain relief devices reinforce end fittings. StopTech Stainless Steel Brake Lines meet DOT Compliance Standards, and every line is 100% tested in-house to a pressure of 4,500 PSI. StopTech brake lines consist of a TeflonĀ® inner line, which is then covered with a layer of stainless steel woven braid. The Teflon tube is very resistant to expansion under pressure and will not degrade from exposure to brake fluid.

The stainless steel braid provides support for the Teflon and the weave is extremely durable against incidental impact and abrasion. Finally, StopTech brake lines are coated with a clear abrasion resistant cover for maximum protection against chaffing and particle intrusion. All necessary brackets and fasteners are included with each line kit. Installation of StopTech Brake Lines typically takes about 3 hours.

Metric line wrenches are are necessary for installation. A fluid flush and bleed will be necessary after installation.

Please observe all safety precautions and follow proper installation guidelines while working on your vehicle. StopTech Stainless Steel Brake Lines are designed as direct replacement parts for stock brake lines. The replacement lines typically follow the same routing as the stock lines. While the design is tolerant of slight modifications to the intended vehicle, any excessive lowering or raising of the vehicle may make the lines unsuitable for use on that particular car, truck, or SUV.

Also, the lines include provisions for routing attachments on the stock suspension, such as brackets on the strut. If an aftermarket suspension is on the vehicle, the stock mounting points may not be on those components. If alternate routing or modifications are required, it is the sole responsibility of the installer to assure that the lines are not binding or touching any part of the suspension or drive train. Inspect the line routing through the entire range of suspension travel, both up and down and left-to-right.

If there is any question as to whether or not the install is correct, do not drive the vehicle until there is absolute assurance the lines are safely routed. When receiving your package, please open all of the boxes immediately to check if all the contents are inside and not damaged. If the product received is defective, a replacement will be sent as soon as possible. I will refuse any damaged or products that are not in good condition. They will inform you on how to proceed based on their policies. I will provide you instructions on how and where to return the product.

All of our products are 100% brand new unless otherwise stated in the description above. As mentioned above, please inspect your order upon receipt. All items (except those exempted) are intended for off road use only, may never be used on public roads and highways.

The item "Stoptech Stainless Steel Braided FRONT & REAR Brake Lines Toyota 4Runner 03-18" is in sale since Wednesday, April 11, 2018. This item is in the category "eBay Motors\Parts & Accessories\Car & Truck Parts\Brakes & Brake Parts\Brake Lines". The seller is "tsukikagesoul811" and is located in Covina, California. This item can be shipped worldwide.

  • Modified Item: No
  • Custom Bundle: No
  • Interchange Part Number: SS-950.44007
  • Surface Finish: Stainless Steel Braided
  • Manufacturer Part Number: 950.44007 + 950.44507
  • Placement on Vehicle: Left
  • Brand: Stoptech
  • Fitment Type: Direct Replacement
  • Non-Domestic Product: No
  • Mounting Hardware Included: Yes

Stoptech Stainless Steel Braided FRONT & REAR Brake Lines Toyota 4Runner 03-18