Front Stainless Braided

ISR (ISIS) Stainless Steel Braided Front & Rear Standard Brake Lines 350z Z33

ISR (ISIS) Stainless Steel Braided Front & Rear Standard Brake Lines 350z Z33
ISR (ISIS) Stainless Steel Braided Front & Rear Standard Brake Lines 350z Z33
ISR (ISIS) Stainless Steel Braided Front & Rear Standard Brake Lines 350z Z33
ISR (ISIS) Stainless Steel Braided Front & Rear Standard Brake Lines 350z Z33

ISR (ISIS) Stainless Steel Braided Front & Rear Standard Brake Lines 350z Z33
STANDARD BRAKES ONLY, WILL NOT FIT BREMBO. This brand new set of ISR Stainless steel braided brake lines is a direct replacement for OEM brake system.

This set of lines will replace your old worn out brake lines with steel braided lines for a noticeable improvement in brake performance. This will result in better braking feel which can translate to later braking points for those better lap times. ISR brake lines are made with precision and the utmost quality control specifications to help you (and us) beat the competition! Brake line installation should be done by a professional mechanic. Read and follow installation instructions completely.

Remove Wheels and drain all brake fluid. Carefully remove existing brake lines from vehicle, avoid splashing paint work with brake fluid.

Make note of positions of C-clip(s), and banjo(s), if used. Remove all crush washers from there mating surfaces. Each new kit comes complete with all of the necessary OEM replacement adapters and Banjo bolts. Clean all sealing surfaces and make sure they are in good condition. Fit these lines starting at the caliper and following the original path of the OEM lines.

Use the new crush washers supplied in your kit. Ensure all location tabs and mounting brackets are properly attached to their mating points on the frame or chassis and are not causing tension on either end of the connection. Do not fully tighten the bolts or threaded ends until the last step of the installation.

Check that the lines are the correct lengths. The hoses should not be kinked or twisted. The opposite axis torque lines should remain parallel along the entire length of the hose. Full travel of the suspension and steering must be checked to ensure the hoses are not stretched or trapped. Tighten banjo bolts and end fittings.

If you're tightening these hoses to a factory hard line, the hard line must be held in place using the correct size wrench. Bolts and end fittings should be tightened to the manufactures recommended torque specs. If not then tighten to 12 to 14 (ft/lbs). You are now ready to bleed the brakes. You must use fresh DOT approved brake fluid and bled the system in accordance to the vehicles manufactures recommendations. Before test driving your vehicle, make a final Check of the lines to ensure all connections are tight and do not leak. The brake pedal should be firm at this stage. After the first 100 miles recheck all the lines and connections for tightness and any leaks.

It is not recommended to mix rubber hoses and stainless steel replacement lines on the same brake system. Do not try to force, rotate or stretch any stainless steel hose assembly; it may cause failure. All ISR Performance Products are Designed for Off Road Use Only. When receiving your package, please open all of the boxes immediately to check if all the contents are inside and not damaged.

If the product received is defective, a replacement will be sent as soon as possible. I will refuse any damaged or products that are not in good condition. They will inform you on how to proceed based on their policies. All of my products are 100% brand new unless otherwise stated in the description above.

As mentioned above, please inspect your order upon receipt. All items (except those exempted) are intended for off road use only, may never be used on public roads and highways. The item "ISR (ISIS) Stainless Steel Braided Front & Rear Standard Brake Lines 350z Z33" is in sale since Wednesday, January 3, 2018. This item is in the category "eBay Motors\Parts & Accessories\Car & Truck Parts\Brakes & Brake Parts\Brake Lines".

The seller is "circuitspecr" and is located in Covina, California. This item can be shipped worldwide.
  • Surface Finish: Stainless Steel
  • Manufacturer Part Number: IS-NIS-1330
  • Placement on Vehicle: Left
  • Brand: ISR Peformance
  • Fitment Type: Direct Replacement

ISR (ISIS) Stainless Steel Braided Front & Rear Standard Brake Lines 350z Z33